SALE - STARRETT
Saw Products Sale
Bondhus Sale
CLOSE OUTS
DeStaCo Sale
Helicoil Thread Repair Kit Sale
PRODUCT LINES
Products
Band Saw Blades
Carr Lane Products
Clamps
Cutting Tools
Hand Saws & Blades
Hand Tools
Jobsite & Construction Tools
Precision Measuring Tools
Bore Gages
Calipers-Dividers-Trammels
Data Collection Systems
Depth Gages
Fixed Gage Standards
Gage Block Sets
Granite Surface Plates
Hardness and Surface Testers
Height Gages
Hole Gages - Slot Gages
Indicator and Gages
Back-Plunger Indicators
Dial Indicators
Electronic Indicators
Indicator Holders and Magnetic Bases
Special Function Indicators
Test Indicators
Machinists Levels - Starrett
Micrometers
Precision Rules, Straight Edges & Parallels
Precision Shop Tools
Protractors & Angle Measurements
Slide Calipers
Squares and Combination Sets
Tool Sets
Threaded Inserts
Starrett Tape Measure Close Out Sale
Videos


665MJZ Starrett Inspection Holder AGD Dial Indicator Set in Case
 
665MJZ Starrett Inspection Holder AGD Dial Indicator Set in Case
    Quantity in Basket: None
    Price: $666.03
     
     
    Quantity:
     

    665MJZ
    Starrett Metric Inspection Holder
    and Dial Indicators


    This is the most versatile dial indicator holder
    with an extremely stable base (A) that is
    8-1/2" (215mm) long x 2-1/4" (57mm) wide
    at the bottom . It can inspect workpieces on
    the top surface of the ground base or within
    a working area defined by the 8" (200mm)
    upright base post (B) and the 9-1/2" (238mm)
    long gage-holding rod (C) . The base post can
    be conveniently located anywhere along the
    8-1/2" (215mm) T-slot in the base .
    This tool can be held in a vise or by a bolt in
    a machine T-slot coming up through one of
    the two 3/8" (9 .5mm) holes in the base and
    fastening down on the top surface .
    D . Swivel Post Snug 665D
    Snug has a .375" (9 .5mm) hole for the gage
    holding rod and a .465" (11 .8mm) hole for
    the upright post . Also comes with the 665L
    Reducing Bushing (J) that can reduce the
    .465" (11 .8mm) hole to 3/8" (9 .5mm) .
    E . Base Reference Guide 665E (Optional)
    Guide is used to check parts or surfaces from
    straight or angular surfaces by use of the
    radiused guide stop . This fits into the T-slot in
    the bottom of the base and is fastened at right
    angles to the length . Push up to or slide along
    a radius surface .
    F . Square Keyway Guide 665F (Optional)
    This guide can also be referenced from a
    square edge, a T-slot or a keyway with at least
    a 1/2" (12 .7mm) width . Has square edges and
    is fastened at right angles to the length . Push
    up to or slide along a square edge .

    Three very useful inspection combinations can
    be made by removing the complete swivel
    post snug and gage holding rod as follows:
    G . Clamp 665G
    Take the clamp and put the clamp post into
    the snug and lock it . Now this combination
    can be used to clamp the gage holding rod
    and the indicator into hard-to-reach places
    for inspecting jigs, fixtures, lining up work on
    centers and machine tables .
    The clamp has a 3" (75mm) capacity and a
    post with an approximately 5-3/4" (145mm)
    length . The clamp post is .464" (11 .8mm)
    diameter that fits into the regular swivel post
    snug 665D .
    Three other clamp post diameter options
    available – 665G-3/8 is a 3/8" (9 .5mm)
    diameter clamp post that can be used in
    the regular swivel post snug 665D with the
    addition of the 665L reducing bushing . The
    665G-5/16 (7 .9mm) and 665G-1/4 (6 .3mm)
    can be used with other snugs to hold an
    indicator .
    H . Tool Post Holder 665H
    Put one end of the offset arm into the swivel
    post snug 665D (with the 665L reducing
    bushing in it) . Then put this rectangular tool
    post holder 665H onto the other arm . This
    combination now allows for a good, tight
    setup in lathe tool posts and other machine
    setups .
    I . Offset Arm 665G-1
    Another very popular measuring combination
    is to put the reducing bushing (which is
    furnished) into the snug and then put one
    leg of the offset arm into it . Now the tool can
    be used in a 3/8" (9 .5mm) chuck or collet to
    sweep a large area .