SALE - STARRETT
Saw Products Sale
Bondhus Sale
CLOSE OUTS
DeStaCo Sale
Helicoil Thread Repair Kit Sale
PRODUCT LINES
Products
Band Saw Blades
Carr Lane Products
Clamps
Cutting Tools
Hand Saws & Blades
Hand Tools
Jobsite & Construction Tools
Precision Measuring Tools
Bore Gages
Calipers-Dividers-Trammels
Data Collection Systems
Depth Gages
Fixed Gage Standards
Gage Block Sets
Granite Surface Plates
Hardness and Surface Testers
Height Gages
Hole Gages - Slot Gages
Indicator and Gages
Back-Plunger Indicators
Dial Indicators
Electronic Indicators
Indicator Holders and Magnetic Bases
Special Function Indicators
Chamfer, Countersink & Hole Gages
Crankshaft, Cylinder & Shaft Gages
Dial Groove Gages
Dial Thickness Gages
Outside, Inside & Interior Dial Caliper Gages
Test Indicators
Machinists Levels - Starrett
Micrometers
Precision Rules, Straight Edges & Parallels
Precision Shop Tools
Protractors & Angle Measurements
Slide Calipers
Squares and Combination Sets
Tool Sets
Threaded Inserts
Starrett Tape Measure Close Out Sale
Videos


696MZ Crankshaft Distortion Gage /Strain Gage with Balancing Attachment 61-458mm Range
 
696MZ  Crankshaft Distortion Gage /Strain Gage with Balancing Attachment 61-458mm Range
    Quantity in Basket: None
    Price: $601.09
     
     
    Quantity:
     

    696MZ
    Starrett Metric Crankshaft Distortion Gage
    61-458mm range

    Ideal gage for checking bearing alignment or shaft deflection without dismantling the engine. Also useful as a strain gage on engine frames. This inside measuring gage checks the distortion of crankshaft webs and bears a direct relation to existing misalignment or excessive bearing wear. Used on all diesel engine shafts and center crankshafts on any type of engine or compressor, the gage can also be applied as a strain gage on engine frames while the engine is operating. A comparison of readings taken at top and bottom positions indicates any misalignment of cylinder and frame which results in local over-stress and eventual cracking of the frame neck. With a special spring tension in the dial indicator, the gage is self-sustaining in any position without sacrificing necessary rigidity, leaving the operator’s hands free. Hardened and ground to a sharp point, conical contact points have an approximate 60º included angle, and will stay in place on 45º surfaces.

    696B Balancing Attachment is furnished with the gage. For certain applications, like turning the crank under test with the gage in place, the attachment can be adjusted to maintain the face of the indicator upward or in desired position. To install on a strain gage in use, remove the knurled clamping nut, then the doweled plate or end strap at either end by the screw. The unit is then positioned over the hubs on two sides of the indicator head. A spring plunger provides the friction that holds the balance in proper relation to position. The parts are nickel plated.

    The dial indicator movement is approximately 5/32" (4mm) and with rods and extension, provides a range from 2 3/8-18" or 61-458mm. There are 10 rods and one extension furnished. Rods are marked to designate the approximate overall length of the gage. Indicator has a movable bezel to adjust the dial in relation to the hand and a non-breakable crystal. Designed in collaboration with Hartford Steam Boiler Inspection and Insurance Company. It was known as the Hartford Steam Boiler Engine Strain Gage and is used by their inspectors to check the distortion of engine shafts and frames.

     

    696 & 696M Crankshaft Distortion Dial/Strain Gages
    Catalog No.
    Range

    Dial Indicator

    Description
    Graduation
    Dial Reading
    Range One Rev.
    696Z
    2-3/8–18"
    .001"
    0-20-0
    .040"
    Strain Gage with Balancing
    Attachment
    696MZ
    61-458mm
    0.02mm
    0-50-0
    1mm
    Millimeter Strain Gage with
    Balancing Attachment
    696B
    Balancing Attachment Only